# defaults to tcp
# CTDB_TRANSPORT="tcp"
-# When set, this variable makes ctdb monitor the amount of free memory
-# in the system (the second number in the buffers/cache output from free -m).
-# If the amount of free memory drops below this treshold the node will become
-# unhealthy and ctdb and all managed services will be shutdown.
+# These setting allow monitoring for low/out-out of memory conditions.
+#
+# If set, once available memory drops below CTDB_MONITOR_FREE_MEMORY_WARN
+# ctdb will start logging messages that memory is low, but will not
+# take any further action.
+#
+# If the amount of free memory drops below CTDB_MONITOR_FREE_MEMORY
+# ctdb will fail all service over to a different node and finally shutdown.
# Once this occurs, the administrator needs to find the reason for the OOM
# situation, rectify it and restart ctdb with "service ctdb start"
# The unit is MByte
-# CTDB_MONITOR_FREE_MEMORY=100
+# CTDB_MONITOR_FREE_MEMORY_WARN=100
+# CTDB_MONITOR_FREE_MEMORY=10
# When set to yes, the CTDB node will start in DISABLED mode and not host
# any public ip addresses. The administrator needs to explicitely enable
# CTDB_NATGW_DEFAULT_GATEWAY=10.0.0.1
# CTDB_NATGW_PRIVATE_NETWORK=10.1.1.0/24
# CTDB_NATGW_NODES=/etc/ctdb/natgw_nodes
+#
+# Normally any node in the natgw group can act as the natgw master.
+# In some configurations you may have special nodes that is a part of the
+# cluster/natgw group, but where the node lacks connectivity to the
+# public network.
+# For these cases, set this variable to make these nodes not able to
+# become natgw master.
+#
+# CTDB_NATGW_SLAVE_ONLY=yes
+
+
+# PER_IP_ROUTING configuration
+#
+# Some setups have multiple network interfaces connected to the
+# same network. By default all traffic for a network is routed
+# through only one interface, while the others are idle.
+#
+# On Linux it possible to use policy based routing to spread the load
+# across all interfaces. The is implemented by using a separate
+# routing table per public ip address.
+#
+# The configuration file configured by CTDB_PER_IP_ROUTING_CONF
+# contains the list of additional routes. The routes are bound to the
+# interface that is holding the public ip address.
+#
+# The format of the config file looks like this:
+# <public_ip_address> <network> [<gateway>]
+# and it's possible to have multiple routes per public ip address.
+#
+# If the special value "__auto_link_local__" is used, the config
+# file autogenerated. Each public ip address gets a special route
+# for its own subnet bound to it's current interface.
+# E.g. 10.1.2.3/24 will result in a config file line
+# 10.1.2.3 10.1.2.0/24
+#
+# The CTDB_PER_IP_ROUTING_RULE_PREF option needs to be configured.
+# The value will be passed as "pref" argument of "ip rule".
+# The value should be between 1 and 32765. So that the rule
+# comes after the rule for "local" routing table and before
+# the rule for the "main" routing table. This way the specific
+# routing table just overloads the "main" routing table,
+# this is useful because with the "__auto_link_local__" setup
+# the default route still comes from the "main" routing table.
+#
+# The routing table ids are automaticly allocated. On
+# Linux the routing table ids must be in the range of 0 to 255.
+# But some are reserved values, see /etc/iproute2/rt_tables.
+# You need to configure a range (CTDB_PER_IP_ROUTING_TABLE_ID_LOW
+# and CTDB_PER_IP_ROUTING_TABLE_ID_HIGH) from which the table ids can be taken.
+#
+# The default value for CTDB_PER_IP_ROUTING_CONF is "",
+# which means the feature is disabled by default.
+#
+# CTDB_PER_IP_ROUTING_CONF="/etc/ctdb/per_ip_routing.conf"
+# CTDB_PER_IP_ROUTING_CONF="__auto_link_local__"
+# CTDB_PER_IP_ROUTING_TABLE_ID_LOW=10
+# CTDB_PER_IP_ROUTING_TABLE_ID_HIGH=250
+# CTDB_PER_IP_ROUTING_RULE_PREF=10000
+
+# Make offline interfaces not a reason for being UNHEALTHY.
+# The CTDB_PARTIALLY_ONLINE_INTERFACES option changes
+# the behavior of the 10.interface monitor event.
+# In some setups it's desired that interfaces without
+# an active link don't change the node to unhealthy.
+# ctdbd is just informed about the interface status
+# and "ctdb status" dislays the node as "PARTIALLYONLINE".
+#
+# CTDB_PARTIALLY_ONLINE_INTERFACES="yes"
# where to log messages
# the default is /var/log/log.ctdb
# The default is "no".
# CTDB_RUN_TIMEOUT_MONITOR=no
+# Should ctdbd start with corrupted/unhealthy persistent databases?
+# This parameter specifies the max error count for persistent health
+# checks before the "startup" event. The value must be a positive
+# interger value, "0" or "-1".
+# The default is "0", which means ctdbd will not start.
+# "-1" means wait forever.
+# CTDB_MAX_PERSISTENT_CHECK_ERRORS=0
+
+# All log entries up to level 9 are also collected into a in-memory ringbuffer
+# in addition to the log that is written to the log file.
+# This parameter controls how many entries we allow for this in memory log
+# CTDB_LOG_RINGBUF_SIZE=500000
+
+#
+#
# set any default tuning options for ctdb
# use CTDB_SET_XXXX=value where XXXX is the name of the tuning
# variable
git.samba.org / metze / ctdb / wip.git / blobdiff