}
/* Setup port 6 interface mode and TRGMII TX circuit */
-static int
-mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
+static void
+mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
{
struct mt7530_priv *priv = ds->priv;
- u32 ncpo1, ssc_delta, trgint, xtal;
-
- xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
+ u32 ncpo1, ssc_delta, xtal;
- if (xtal == HWTRAP_XTAL_20MHZ) {
- dev_err(priv->dev,
- "%s: MT7530 with a 20MHz XTAL is not supported!\n",
- __func__);
- return -EINVAL;
- }
+ /* Disable the MT7530 TRGMII clocks */
+ core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
- switch (interface) {
- case PHY_INTERFACE_MODE_RGMII:
- trgint = 0;
- break;
- case PHY_INTERFACE_MODE_TRGMII:
- trgint = 1;
- if (xtal == HWTRAP_XTAL_25MHZ)
- ssc_delta = 0x57;
- else
- ssc_delta = 0x87;
- if (priv->id == ID_MT7621) {
- /* PLL frequency: 125MHz: 1.0GBit */
- if (xtal == HWTRAP_XTAL_40MHZ)
- ncpo1 = 0x0640;
- if (xtal == HWTRAP_XTAL_25MHZ)
- ncpo1 = 0x0a00;
- } else { /* PLL frequency: 250MHz: 2.0Gbit */
- if (xtal == HWTRAP_XTAL_40MHZ)
- ncpo1 = 0x0c80;
- if (xtal == HWTRAP_XTAL_25MHZ)
- ncpo1 = 0x1400;
- }
- break;
- default:
- dev_err(priv->dev, "xMII interface %d not supported\n",
- interface);
- return -EINVAL;
+ if (interface == PHY_INTERFACE_MODE_RGMII) {
+ mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
+ P6_INTF_MODE(0));
+ return;
}
- mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
- P6_INTF_MODE(trgint));
+ mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK, P6_INTF_MODE(1));
- if (trgint) {
- /* Disable the MT7530 TRGMII clocks */
- core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
+ xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
- /* Setup the MT7530 TRGMII Tx Clock */
- core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
- core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
- core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
- core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
- core_write(priv, CORE_PLL_GROUP4,
- RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
- RG_SYSPLL_BIAS_LPF_EN);
- core_write(priv, CORE_PLL_GROUP2,
- RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
- RG_SYSPLL_POSDIV(1));
- core_write(priv, CORE_PLL_GROUP7,
- RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
- RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
+ if (xtal == HWTRAP_XTAL_25MHZ)
+ ssc_delta = 0x57;
+ else
+ ssc_delta = 0x87;
- /* Enable the MT7530 TRGMII clocks */
- core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
+ if (priv->id == ID_MT7621) {
+ /* PLL frequency: 125MHz: 1.0GBit */
+ if (xtal == HWTRAP_XTAL_40MHZ)
+ ncpo1 = 0x0640;
+ if (xtal == HWTRAP_XTAL_25MHZ)
+ ncpo1 = 0x0a00;
+ } else { /* PLL frequency: 250MHz: 2.0Gbit */
+ if (xtal == HWTRAP_XTAL_40MHZ)
+ ncpo1 = 0x0c80;
+ if (xtal == HWTRAP_XTAL_25MHZ)
+ ncpo1 = 0x1400;
}
- return 0;
-}
+ /* Setup the MT7530 TRGMII Tx Clock */
+ core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
+ core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
+ core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
+ core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
+ core_write(priv, CORE_PLL_GROUP4, RG_SYSPLL_DDSFBK_EN |
+ RG_SYSPLL_BIAS_EN | RG_SYSPLL_BIAS_LPF_EN);
+ core_write(priv, CORE_PLL_GROUP2, RG_SYSPLL_EN_NORMAL |
+ RG_SYSPLL_VODEN | RG_SYSPLL_POSDIV(1));
+ core_write(priv, CORE_PLL_GROUP7, RG_LCDDS_PCW_NCPO_CHG |
+ RG_LCCDS_C(3) | RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
-static bool mt7531_dual_sgmii_supported(struct mt7530_priv *priv)
-{
- u32 val;
-
- val = mt7530_read(priv, MT7531_TOP_SIG_SR);
-
- return (val & PAD_DUAL_SGMII_EN) != 0;
-}
-
-static int
-mt7531_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
-{
- return 0;
+ /* Enable the MT7530 TRGMII clocks */
+ core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
}
static void
u32 xtal;
u32 val;
- if (mt7531_dual_sgmii_supported(priv))
- return;
-
val = mt7530_read(priv, MT7531_CREV);
top_sig = mt7530_read(priv, MT7531_TOP_SIG_SR);
hwstrap = mt7530_read(priv, MT7531_HWTRAP);
return "PHY P4";
case P5_INTF_SEL_GMAC5:
return "GMAC5";
- case P5_INTF_SEL_GMAC5_SGMII:
- return "GMAC5_SGMII";
default:
return "unknown";
}
/* MT7530_P5_MODE_GMAC: P5 -> External phy or 2nd GMAC */
val &= ~MHWTRAP_P5_DIS;
break;
- case P5_DISABLED:
- interface = PHY_INTERFACE_MODE_NA;
- break;
default:
- dev_err(ds->dev, "Unsupported p5_intf_sel %d\n",
- priv->p5_intf_sel);
- goto unlock_exit;
+ break;
}
/* Setup RGMII settings */
dev_dbg(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));
- priv->p5_interface = interface;
-
-unlock_exit:
mutex_unlock(&priv->reg_mutex);
}
static void
mt753x_trap_frames(struct mt7530_priv *priv)
{
- /* Trap BPDUs to the CPU port(s) */
- mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
+ /* Trap 802.1X PAE frames and BPDUs to the CPU port(s) and egress them
+ * VLAN-untagged.
+ */
+ mt7530_rmw(priv, MT753X_BPC, MT753X_PAE_EG_TAG_MASK |
+ MT753X_PAE_PORT_FW_MASK | MT753X_BPDU_EG_TAG_MASK |
+ MT753X_BPDU_PORT_FW_MASK,
+ MT753X_PAE_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
+ MT753X_PAE_PORT_FW(MT753X_BPDU_CPU_ONLY) |
+ MT753X_BPDU_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
MT753X_BPDU_CPU_ONLY);
- /* Trap 802.1X PAE frames to the CPU port(s) */
- mt7530_rmw(priv, MT753X_BPC, MT753X_PAE_PORT_FW_MASK,
- MT753X_PAE_PORT_FW(MT753X_BPDU_CPU_ONLY));
-
- /* Trap LLDP frames with :0E MAC DA to the CPU port(s) */
- mt7530_rmw(priv, MT753X_RGAC2, MT753X_R0E_PORT_FW_MASK,
+ /* Trap LLDP frames with :0E MAC DA to the CPU port(s) and egress them
+ * VLAN-untagged.
+ */
+ mt7530_rmw(priv, MT753X_RGAC2, MT753X_R0E_EG_TAG_MASK |
+ MT753X_R0E_PORT_FW_MASK,
+ MT753X_R0E_EG_TAG(MT7530_VLAN_EG_UNTAGGED) |
MT753X_R0E_PORT_FW(MT753X_BPDU_CPU_ONLY));
}
-static int
+static void
mt753x_cpu_port_enable(struct dsa_switch *ds, int port)
{
struct mt7530_priv *priv = ds->priv;
- int ret;
-
- /* Setup max capability of CPU port at first */
- if (priv->info->cpu_port_config) {
- ret = priv->info->cpu_port_config(ds, port);
- if (ret)
- return ret;
- }
/* Enable Mediatek header mode on the cpu port */
mt7530_write(priv, MT7530_PVC_P(port),
mt7530_set(priv, MT7530_MFC, BC_FFP(BIT(port)) | UNM_FFP(BIT(port)) |
UNU_FFP(BIT(port)));
- /* Set CPU port number */
- if (priv->id == ID_MT7530 || priv->id == ID_MT7621)
- mt7530_rmw(priv, MT7530_MFC, CPU_MASK, CPU_EN | CPU_PORT(port));
-
/* Add the CPU port to the CPU port bitmap for MT7531 and the switch on
* the MT7988 SoC. Trapped frames will be forwarded to the CPU port that
* is affine to the inbound user port.
/* Set to fallback mode for independent VLAN learning */
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_PORT_VLAN_MASK,
MT7530_PORT_FALLBACK_MODE);
-
- return 0;
}
static int
priv->ports[port].enable = true;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
priv->ports[port].pm);
- mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
mutex_unlock(&priv->reg_mutex);
priv->ports[port].enable = false;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
PCR_MATRIX_CLR);
- mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
mutex_unlock(&priv->reg_mutex);
}
}
/* This register must be set for MT7530 to properly fire interrupts */
- if (priv->id != ID_MT7531)
+ if (priv->id == ID_MT7530 || priv->id == ID_MT7621)
mt7530_set(priv, MT7530_TOP_SIG_CTRL, TOP_SIG_CTRL_NORMAL);
ret = request_threaded_irq(priv->irq, NULL, mt7530_irq_thread_fn,
static void
mt7530_free_irq(struct mt7530_priv *priv)
{
- mt7530_free_mdio_irq(priv);
+ struct device_node *mnp, *np = priv->dev->of_node;
+
+ mnp = of_get_child_by_name(np, "mdio");
+ if (!mnp)
+ mt7530_free_mdio_irq(priv);
+ of_node_put(mnp);
+
mt7530_free_irq_common(priv);
}
static int
mt7530_setup_mdio(struct mt7530_priv *priv)
{
+ struct device_node *mnp, *np = priv->dev->of_node;
struct dsa_switch *ds = priv->ds;
struct device *dev = priv->dev;
struct mii_bus *bus;
static int idx;
- int ret;
+ int ret = 0;
+
+ mnp = of_get_child_by_name(np, "mdio");
+
+ if (mnp && !of_device_is_available(mnp))
+ goto out;
bus = devm_mdiobus_alloc(dev);
- if (!bus)
- return -ENOMEM;
+ if (!bus) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ if (!mnp)
+ ds->user_mii_bus = bus;
- ds->user_mii_bus = bus;
bus->priv = priv;
bus->name = KBUILD_MODNAME "-mii";
snprintf(bus->id, MII_BUS_ID_SIZE, KBUILD_MODNAME "-%d", idx++);
bus->parent = dev;
bus->phy_mask = ~ds->phys_mii_mask;
- if (priv->irq)
+ if (priv->irq && !mnp)
mt7530_setup_mdio_irq(priv);
- ret = devm_mdiobus_register(dev, bus);
+ ret = devm_of_mdiobus_register(dev, bus, mnp);
if (ret) {
dev_err(dev, "failed to register MDIO bus: %d\n", ret);
- if (priv->irq)
+ if (priv->irq && !mnp)
mt7530_free_mdio_irq(priv);
}
+out:
+ of_node_put(mnp);
return ret;
}
*/
if (priv->mcm) {
reset_control_assert(priv->rstc);
- usleep_range(1000, 1100);
+ usleep_range(5000, 5100);
reset_control_deassert(priv->rstc);
} else {
gpiod_set_value_cansleep(priv->reset, 0);
- usleep_range(1000, 1100);
+ usleep_range(5000, 5100);
gpiod_set_value_cansleep(priv->reset, 1);
}
return -ENODEV;
}
+ if ((val & HWTRAP_XTAL_MASK) == HWTRAP_XTAL_20MHZ) {
+ dev_err(priv->dev,
+ "MT7530 with a 20MHz XTAL is not supported!\n");
+ return -EINVAL;
+ }
+
/* Reset the switch through internal reset */
mt7530_write(priv, MT7530_SYS_CTRL,
SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
val |= MHWTRAP_MANUAL;
mt7530_write(priv, MT7530_MHWTRAP, val);
- priv->p6_interface = PHY_INTERFACE_MODE_NA;
-
mt753x_trap_frames(priv);
/* Enable and reset MIB counters */
mt7530_mib_reset(ds);
for (i = 0; i < MT7530_NUM_PORTS; i++) {
+ /* Clear link settings and enable force mode to force link down
+ * on all ports until they're enabled later.
+ */
+ mt7530_rmw(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
+ PMCR_FORCE_MODE, PMCR_FORCE_MODE);
+
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
PCR_MATRIX_CLR);
mt7530_set(priv, MT7530_PSC_P(i), SA_DIS);
if (dsa_is_cpu_port(ds, i)) {
- ret = mt753x_cpu_port_enable(ds, i);
- if (ret)
- return ret;
+ mt753x_cpu_port_enable(ds, i);
} else {
mt7530_port_disable(ds, i);
return ret;
/* Setup port 5 */
- priv->p5_intf_sel = P5_DISABLED;
- interface = PHY_INTERFACE_MODE_NA;
-
if (!dsa_is_unused_port(ds, 5)) {
priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
- ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface);
- if (ret && ret != -ENODEV)
- return ret;
} else {
- /* Scan the ethernet nodes. look for GMAC1, lookup used phy */
+ /* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY.
+ * Set priv->p5_intf_sel to the appropriate value if PHY muxing
+ * is detected.
+ */
for_each_child_of_node(dn, mac_np) {
if (!of_device_is_compatible(mac_np,
"mediatek,eth-mac"))
of_node_put(phy_node);
break;
}
+
+ if (priv->p5_intf_sel == P5_INTF_SEL_PHY_P0 ||
+ priv->p5_intf_sel == P5_INTF_SEL_PHY_P4)
+ mt7530_setup_port5(ds, interface);
}
#ifdef CONFIG_GPIOLIB
}
#endif /* CONFIG_GPIOLIB */
- mt7530_setup_port5(ds, interface);
-
/* Flush the FDB table */
ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
if (ret < 0)
UNU_FFP_MASK);
for (i = 0; i < MT7530_NUM_PORTS; i++) {
+ /* Clear link settings and enable force mode to force link down
+ * on all ports until they're enabled later.
+ */
+ mt7530_rmw(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
+ MT7531_FORCE_MODE, MT7531_FORCE_MODE);
+
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
PCR_MATRIX_CLR);
mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
if (dsa_is_cpu_port(ds, i)) {
- ret = mt753x_cpu_port_enable(ds, i);
- if (ret)
- return ret;
+ mt753x_cpu_port_enable(ds, i);
} else {
mt7530_port_disable(ds, i);
*/
if (priv->mcm) {
reset_control_assert(priv->rstc);
- usleep_range(1000, 1100);
+ usleep_range(5000, 5100);
reset_control_deassert(priv->rstc);
} else {
gpiod_set_value_cansleep(priv->reset, 0);
- usleep_range(1000, 1100);
+ usleep_range(5000, 5100);
gpiod_set_value_cansleep(priv->reset, 1);
}
return -ENODEV;
}
- /* all MACs must be forced link-down before sw reset */
+ /* MT7531AE has got two SGMII units. One for port 5, one for port 6.
+ * MT7531BE has got only one SGMII unit which is for port 6.
+ */
+ val = mt7530_read(priv, MT7531_TOP_SIG_SR);
+ priv->p5_sgmii = !!(val & PAD_DUAL_SGMII_EN);
+
+ /* Force link down on all ports before internal reset */
for (i = 0; i < MT7530_NUM_PORTS; i++)
mt7530_write(priv, MT7530_PMCR_P(i), MT7531_FORCE_LNK);
/* Reset the switch through internal reset */
- mt7530_write(priv, MT7530_SYS_CTRL,
- SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
- SYS_CTRL_REG_RST);
-
- mt7531_pll_setup(priv);
-
- if (mt7531_dual_sgmii_supported(priv)) {
- priv->p5_intf_sel = P5_INTF_SEL_GMAC5_SGMII;
+ mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_SW_RST | SYS_CTRL_REG_RST);
+ if (!priv->p5_sgmii) {
+ mt7531_pll_setup(priv);
+ } else {
/* Let ds->user_mii_bus be able to access external phy. */
mt7530_rmw(priv, MT7531_GPIO_MODE1, MT7531_GPIO11_RG_RXD2_MASK,
MT7531_EXT_P_MDC_11);
mt7530_rmw(priv, MT7531_GPIO_MODE1, MT7531_GPIO12_RG_RXD3_MASK,
MT7531_EXT_P_MDIO_12);
- } else {
- priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
}
- dev_dbg(ds->dev, "P5 support %s interface\n",
- p5_intf_modes(priv->p5_intf_sel));
+
+ if (!dsa_is_unused_port(ds, 5))
+ priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
mt7530_rmw(priv, MT7531_GPIO_MODE0, MT7531_GPIO0_MASK,
MT7531_GPIO0_INTERRUPT);
- /* Let phylink decide the interface later. */
- priv->p5_interface = PHY_INTERFACE_MODE_NA;
- priv->p6_interface = PHY_INTERFACE_MODE_NA;
-
/* Enable PHY core PLL, since phy_device has not yet been created
* provided for phy_[read,write]_mmd_indirect is called, we provide
* our own mt7531_ind_mmd_phy_[read,write] to complete this
struct phylink_config *config)
{
switch (port) {
- case 0 ... 4: /* Internal phy */
+ /* Ports which are connected to switch PHYs. There is no MII pinout. */
+ case 0 ... 4:
__set_bit(PHY_INTERFACE_MODE_GMII,
config->supported_interfaces);
break;
- case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+ /* Port 5 supports rgmii with delays, mii, and gmii. */
+ case 5:
phy_interface_set_rgmii(config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_MII,
config->supported_interfaces);
config->supported_interfaces);
break;
- case 6: /* 1st cpu port */
+ /* Port 6 supports rgmii and trgmii. */
+ case 6:
__set_bit(PHY_INTERFACE_MODE_RGMII,
config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_TRGMII,
}
}
-static bool mt7531_is_rgmii_port(struct mt7530_priv *priv, u32 port)
-{
- return (port == 5) && (priv->p5_intf_sel != P5_INTF_SEL_GMAC5_SGMII);
-}
-
static void mt7531_mac_port_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
{
struct mt7530_priv *priv = ds->priv;
switch (port) {
- case 0 ... 4: /* Internal phy */
+ /* Ports which are connected to switch PHYs. There is no MII pinout. */
+ case 0 ... 4:
__set_bit(PHY_INTERFACE_MODE_GMII,
config->supported_interfaces);
break;
- case 5: /* 2nd cpu port supports either rgmii or sgmii/8023z */
- if (mt7531_is_rgmii_port(priv, port)) {
+ /* Port 5 supports rgmii with delays on MT7531BE, sgmii/802.3z on
+ * MT7531AE.
+ */
+ case 5:
+ if (!priv->p5_sgmii) {
phy_interface_set_rgmii(config->supported_interfaces);
break;
}
fallthrough;
- case 6: /* 1st cpu port supports sgmii/8023z only */
+ /* Port 6 supports sgmii/802.3z. */
+ case 6:
__set_bit(PHY_INTERFACE_MODE_SGMII,
config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_1000BASEX,
static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
{
- phy_interface_zero(config->supported_interfaces);
-
switch (port) {
- case 0 ... 4: /* Internal phy */
+ /* Ports which are connected to switch PHYs. There is no MII pinout. */
+ case 0 ... 3:
__set_bit(PHY_INTERFACE_MODE_INTERNAL,
config->supported_interfaces);
break;
+ /* Port 6 is connected to SoC's XGMII MAC. There is no MII pinout. */
case 6:
__set_bit(PHY_INTERFACE_MODE_INTERNAL,
config->supported_interfaces);
}
}
-static int
-mt753x_pad_setup(struct dsa_switch *ds, const struct phylink_link_state *state)
-{
- struct mt7530_priv *priv = ds->priv;
-
- return priv->info->pad_setup(ds, state->interface);
-}
-
-static int
+static void
mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phy_interface_t interface)
{
struct mt7530_priv *priv = ds->priv;
- /* Only need to setup port5. */
- if (port != 5)
- return 0;
-
- mt7530_setup_port5(priv->ds, interface);
-
- return 0;
+ if (port == 5)
+ mt7530_setup_port5(priv->ds, interface);
+ else if (port == 6)
+ mt7530_setup_port6(priv->ds, interface);
}
-static int mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
- phy_interface_t interface,
- struct phy_device *phydev)
+static void mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
+ phy_interface_t interface,
+ struct phy_device *phydev)
{
u32 val;
- if (!mt7531_is_rgmii_port(priv, port)) {
- dev_err(priv->dev, "RGMII mode is not available for port %d\n",
- port);
- return -EINVAL;
- }
-
val = mt7530_read(priv, MT7531_CLKGEN_CTRL);
val |= GP_CLK_EN;
val &= ~GP_MODE_MASK;
case PHY_INTERFACE_MODE_RGMII_ID:
break;
default:
- return -EINVAL;
+ break;
}
}
- mt7530_write(priv, MT7531_CLKGEN_CTRL, val);
-
- return 0;
-}
-
-static bool mt753x_is_mac_port(u32 port)
-{
- return (port == 5 || port == 6);
-}
-
-static int
-mt7988_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
- phy_interface_t interface)
-{
- if (dsa_is_cpu_port(ds, port) &&
- interface == PHY_INTERFACE_MODE_INTERNAL)
- return 0;
- return -EINVAL;
+ mt7530_write(priv, MT7531_CLKGEN_CTRL, val);
}
-static int
+static void
mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phy_interface_t interface)
{
struct phy_device *phydev;
struct dsa_port *dp;
- if (!mt753x_is_mac_port(port)) {
- dev_err(priv->dev, "port %d is not a MAC port\n", port);
- return -EINVAL;
- }
-
- switch (interface) {
- case PHY_INTERFACE_MODE_RGMII:
- case PHY_INTERFACE_MODE_RGMII_ID:
- case PHY_INTERFACE_MODE_RGMII_RXID:
- case PHY_INTERFACE_MODE_RGMII_TXID:
+ if (phy_interface_mode_is_rgmii(interface)) {
dp = dsa_to_port(ds, port);
phydev = dp->user->phydev;
- return mt7531_rgmii_setup(priv, port, interface, phydev);
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_NA:
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_2500BASEX:
- /* handled in SGMII PCS driver */
- return 0;
- default:
- return -EINVAL;
+ mt7531_rgmii_setup(priv, port, interface, phydev);
}
-
- return -EINVAL;
-}
-
-static int
-mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
- const struct phylink_link_state *state)
-{
- struct mt7530_priv *priv = ds->priv;
-
- return priv->info->mac_port_config(ds, port, mode, state->interface);
}
static struct phylink_pcs *
const struct phylink_link_state *state)
{
struct mt7530_priv *priv = ds->priv;
- u32 mcr_cur, mcr_new;
-
- switch (port) {
- case 0 ... 4: /* Internal phy */
- if (state->interface != PHY_INTERFACE_MODE_GMII &&
- state->interface != PHY_INTERFACE_MODE_INTERNAL)
- goto unsupported;
- break;
- case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
- if (priv->p5_interface == state->interface)
- break;
-
- if (mt753x_mac_config(ds, port, mode, state) < 0)
- goto unsupported;
-
- if (priv->p5_intf_sel != P5_DISABLED)
- priv->p5_interface = state->interface;
- break;
- case 6: /* 1st cpu port */
- if (priv->p6_interface == state->interface)
- break;
-
- mt753x_pad_setup(ds, state);
- if (mt753x_mac_config(ds, port, mode, state) < 0)
- goto unsupported;
-
- priv->p6_interface = state->interface;
- break;
- default:
-unsupported:
- dev_err(ds->dev, "%s: unsupported %s port: %i\n",
- __func__, phy_modes(state->interface), port);
- return;
- }
-
- mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
- mcr_new = mcr_cur;
- mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
- mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
- PMCR_BACKPR_EN | PMCR_FORCE_MODE_ID(priv->id);
+ if ((port == 5 || port == 6) && priv->info->mac_port_config)
+ priv->info->mac_port_config(ds, port, mode, state->interface);
/* Are we connected to external phy */
if (port == 5 && dsa_is_user_port(ds, 5))
- mcr_new |= PMCR_EXT_PHY;
-
- if (mcr_new != mcr_cur)
- mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
+ mt7530_set(priv, MT7530_PMCR_P(port), PMCR_EXT_PHY);
}
static void mt753x_phylink_mac_link_down(struct dsa_switch *ds, int port,
mcr = PMCR_RX_EN | PMCR_TX_EN | PMCR_FORCE_LNK;
- /* MT753x MAC works in 1G full duplex mode for all up-clocked
- * variants.
- */
- if (interface == PHY_INTERFACE_MODE_TRGMII ||
- (phy_interface_mode_is_8023z(interface))) {
- speed = SPEED_1000;
- duplex = DUPLEX_FULL;
- }
-
switch (speed) {
case SPEED_1000:
+ case SPEED_2500:
+ case SPEED_10000:
mcr |= PMCR_FORCE_SPEED_1000;
break;
case SPEED_100:
if (mode == MLO_AN_PHY && phydev && phy_init_eee(phydev, false) >= 0) {
switch (speed) {
case SPEED_1000:
+ case SPEED_2500:
mcr |= PMCR_FORCE_EEE1G;
break;
case SPEED_100:
mt7530_set(priv, MT7530_PMCR_P(port), mcr);
}
-static int
-mt7531_cpu_port_config(struct dsa_switch *ds, int port)
-{
- struct mt7530_priv *priv = ds->priv;
- phy_interface_t interface;
- int speed;
- int ret;
-
- switch (port) {
- case 5:
- if (mt7531_is_rgmii_port(priv, port))
- interface = PHY_INTERFACE_MODE_RGMII;
- else
- interface = PHY_INTERFACE_MODE_2500BASEX;
-
- priv->p5_interface = interface;
- break;
- case 6:
- interface = PHY_INTERFACE_MODE_2500BASEX;
-
- priv->p6_interface = interface;
- break;
- default:
- return -EINVAL;
- }
-
- if (interface == PHY_INTERFACE_MODE_2500BASEX)
- speed = SPEED_2500;
- else
- speed = SPEED_1000;
-
- ret = mt7531_mac_config(ds, port, MLO_AN_FIXED, interface);
- if (ret)
- return ret;
- mt7530_write(priv, MT7530_PMCR_P(port),
- PMCR_CPU_PORT_SETTING(priv->id));
- mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED, interface, NULL,
- speed, DUPLEX_FULL, true, true);
-
- return 0;
-}
-
-static int
-mt7988_cpu_port_config(struct dsa_switch *ds, int port)
-{
- struct mt7530_priv *priv = ds->priv;
-
- mt7530_write(priv, MT7530_PMCR_P(port),
- PMCR_CPU_PORT_SETTING(priv->id));
-
- mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED,
- PHY_INTERFACE_MODE_INTERNAL, NULL,
- SPEED_10000, DUPLEX_FULL, true, true);
-
- return 0;
-}
-
static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
{
mt753x_setup(struct dsa_switch *ds)
{
struct mt7530_priv *priv = ds->priv;
- int i, ret;
-
- /* Initialise the PCS devices */
- for (i = 0; i < priv->ds->num_ports; i++) {
- priv->pcs[i].pcs.ops = priv->info->pcs_ops;
- priv->pcs[i].pcs.neg_mode = true;
- priv->pcs[i].priv = priv;
- priv->pcs[i].port = i;
- }
+ int ret = priv->info->sw_setup(ds);
+ int i;
- ret = priv->info->sw_setup(ds);
if (ret)
return ret;
if (ret && priv->irq)
mt7530_free_irq_common(priv);
+ /* Initialise the PCS devices */
+ for (i = 0; i < priv->ds->num_ports; i++) {
+ priv->pcs[i].pcs.ops = priv->info->pcs_ops;
+ priv->pcs[i].pcs.neg_mode = true;
+ priv->pcs[i].priv = priv;
+ priv->pcs[i].port = i;
+ }
+
if (priv->create_sgmii) {
- ret = priv->create_sgmii(priv, mt7531_dual_sgmii_supported(priv));
+ ret = priv->create_sgmii(priv);
if (ret && priv->irq)
mt7530_free_irq(priv);
}
}
static int mt753x_get_mac_eee(struct dsa_switch *ds, int port,
- struct ethtool_eee *e)
+ struct ethtool_keee *e)
{
struct mt7530_priv *priv = ds->priv;
u32 eeecr = mt7530_read(priv, MT7530_PMEEECR_P(port));
}
static int mt753x_set_mac_eee(struct dsa_switch *ds, int port,
- struct ethtool_eee *e)
+ struct ethtool_keee *e)
{
struct mt7530_priv *priv = ds->priv;
u32 set, mask = LPI_THRESH_MASK | LPI_MODE_EN;
return 0;
}
-static int mt7988_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
+static void
+mt753x_conduit_state_change(struct dsa_switch *ds,
+ const struct net_device *conduit,
+ bool operational)
{
- return 0;
+ struct dsa_port *cpu_dp = conduit->dsa_ptr;
+ struct mt7530_priv *priv = ds->priv;
+ int val = 0;
+ u8 mask;
+
+ /* Set the CPU port to trap frames to for MT7530. Trapped frames will be
+ * forwarded to the numerically smallest CPU port whose conduit
+ * interface is up.
+ */
+ if (priv->id != ID_MT7530 && priv->id != ID_MT7621)
+ return;
+
+ mask = BIT(cpu_dp->index);
+
+ if (operational)
+ priv->active_cpu_ports |= mask;
+ else
+ priv->active_cpu_ports &= ~mask;
+
+ if (priv->active_cpu_ports)
+ val = CPU_EN | CPU_PORT(__ffs(priv->active_cpu_ports));
+
+ mt7530_rmw(priv, MT7530_MFC, CPU_EN | CPU_PORT_MASK, val);
}
static int mt7988_setup(struct dsa_switch *ds)
.phylink_mac_link_up = mt753x_phylink_mac_link_up,
.get_mac_eee = mt753x_get_mac_eee,
.set_mac_eee = mt753x_set_mac_eee,
+ .conduit_state_change = mt753x_conduit_state_change,
};
EXPORT_SYMBOL_GPL(mt7530_switch_ops);
.phy_write_c22 = mt7530_phy_write_c22,
.phy_read_c45 = mt7530_phy_read_c45,
.phy_write_c45 = mt7530_phy_write_c45,
- .pad_setup = mt7530_pad_clk_setup,
.mac_port_get_caps = mt7530_mac_port_get_caps,
.mac_port_config = mt7530_mac_config,
},
.phy_write_c22 = mt7530_phy_write_c22,
.phy_read_c45 = mt7530_phy_read_c45,
.phy_write_c45 = mt7530_phy_write_c45,
- .pad_setup = mt7530_pad_clk_setup,
.mac_port_get_caps = mt7530_mac_port_get_caps,
.mac_port_config = mt7530_mac_config,
},
.phy_write_c22 = mt7531_ind_c22_phy_write,
.phy_read_c45 = mt7531_ind_c45_phy_read,
.phy_write_c45 = mt7531_ind_c45_phy_write,
- .pad_setup = mt7531_pad_setup,
- .cpu_port_config = mt7531_cpu_port_config,
.mac_port_get_caps = mt7531_mac_port_get_caps,
.mac_port_config = mt7531_mac_config,
},
.phy_write_c22 = mt7531_ind_c22_phy_write,
.phy_read_c45 = mt7531_ind_c45_phy_read,
.phy_write_c45 = mt7531_ind_c45_phy_write,
- .pad_setup = mt7988_pad_setup,
- .cpu_port_config = mt7988_cpu_port_config,
.mac_port_get_caps = mt7988_mac_port_get_caps,
- .mac_port_config = mt7988_mac_config,
},
};
EXPORT_SYMBOL_GPL(mt753x_table);
/* Sanity check if these required device operations are filled
* properly.
*/
- if (!priv->info->sw_setup || !priv->info->pad_setup ||
- !priv->info->phy_read_c22 || !priv->info->phy_write_c22 ||
- !priv->info->mac_port_get_caps ||
- !priv->info->mac_port_config)
+ if (!priv->info->sw_setup || !priv->info->phy_read_c22 ||
+ !priv->info->phy_write_c22 || !priv->info->mac_port_get_caps)
return -EINVAL;
priv->id = priv->info->id;
git.samba.org / sfrench / cifs-2.6.git / blobdiff